torsdag 24 december 2015

Merry christmas 2015


Merry Christmas 2015 

Back in October I continued to mess around with the gear box,  the temperature dropped rapidly and I found my self again working in the cold at around zero degrees and to a dead line... I needed to get the gear box back together, in the bus and the hubs and brakes on so I could roll the bus on a trailor and get it moved to its new place - the warm garage in Enköping - I was a little concerned that we would get a full on winter and I would find my self in the messy situation of trying to transport a bus in the snow - ( I need not have worried so much as those bad winters seem to be a thing of the past)


Anyway after a particular frustrating episode I left the garage and gave it some thought, this is a solution I use a lot now, I returned and all went well, its amazing what a night or 2 away form the problem can do.

I managed to get the drive shafts back in, like it is supposed to be, get the one piece rubber boots on and then on my own lift it in to place, this was pretty tricky, laying on my back wiggling the box in on the jack and balancing the whole thing on a couple of extra jack stands.

I was on my way now, the next job was the front beam, I knocked out the old bushes and installed some new ones as I was not happy with the gap, reamed them again and this time was happier then I called my pal Panos up to help, he came over after work one day.

After just a little bit of head scratching and pulling we had the thing ready to go up, and it did pretty much with out any hassle - we then fitted the drop arm, that took a bit of messing around with made up shims and the arm needs to compress the spring washer but allow the top of the pin - anyway in the end after a few attempts we had it in just like it should be.

 

 I also fitted the steering tube and box in to the bus, again trick on your own but it can be done.


So then I threw on the wheels, dropped it back down to earth.
That week I was off, so I borrowed the works van, moved the entire garage and once that was done I hired a car tailor from the local OKQ8 at skolsta,  borrowed suz car (VW CC auto 4wd) got the bus strapped on too kit over to the new garage.


Bus in the new garage - Enköping


work space taking shape

So that brings us up to date...

This last few weeks I have began hanging doors, checking alignment and cleaning the threads everywhere, I have changed the 6 v wiper motor to 12 v. Found out that the doors are as slightly different shade of red, so they have to go back to be resprayed in January.
The belly pans have now been sprayed in the sealing wax red.

This week I have been over to Hans - I talked to him about engines and from his expert advice I decided not to go crazy - He will build a 1776 and run it with single 34 carb to start with.
311 heads'
35.5 intake/ 32 exhaust twin port heads
311 rods
Dual relief case
Alternator internal reg
38 mm csp heat exchangers
38 mm csp python exhaust
Swivel "ball" rockers
200 mm flywheel for 12v starter motor
Python 38 exhaust


Clutch - 9 spring  - note have to check if I have one of these....and the tin ware.

have to start thinking about - Temp gauge, oil pressure and fuel gauge.....

I have also possible found some one locally to come and take a look at the head lining....

Soon new year - middle days between now and then im hoping to get in the garage and start threading the wiring loom into place and continue with the deluxe trim polishing, also cleaning and painting up the sunroof parts...

Steves new list:
order this

Headlights - sealed beam units -bosch?
gauges
cluch
tinware
airfliters that look and work well
rear brakes hoses - braided...and mounts/clips
re-chrome golde handle
see about seat covering - headlining
start reading about woodwork....















söndag 4 oktober 2015

Today in the garage - fitting axle boots

I thought I would be getting a lot done today, but it was one of those days where things don't go as smoothly as you hoped - I had a lot of grief with the removal of the axle tubes and had to make a new gasket, made one and fitted it and then found it was still too tight, so all off again and a thin one installed, that did the trick - then on to the other side, the gasket sealant that I had used before (back when i was test fitting at Pekas) had stuck the paper shims together . so more gaskets needed and then more probs with the tubes not wanting to fit as I still had the bearings in the hubs and that caused grief, I think the shim had cocked in the bearing carrier, lots of banging and pulling and huffing and puffing - got there in the end though .






Then it was time to get home, I have the rear kinda ready to fit to the bus again, so I plan to tidy up the rear brake hubs etc and install them after Ive fitted the gearbox back in to the chassis.

Next job is to get the front beam ready to fit back in, I need to grind a little form the front flipped spindle so that it allows the disc brake to rotate without scraping - this is the next job. After that Im gonna get the bus back on jack stands and fit the front and back suspension, at least then I can be nearer to moving it on the trailer to the new garage place for this winter - I would really like to finish installing the hard brake lines (just some holes to be drilled and fasteners fitted) and get the wiring loom in and spray the under side with black paint and under sealer.... only got a couple of half weekends left until autumn break....

lördag 3 oktober 2015

Are you crazy enough for the Volkswagen Station Wagon?





Autumn time....


Its that time again, the birds leave Hjälsta and the buses return.

Dan came by and dropped his high roof of for the winter hibernation, we had a coffee and a chat at the garage and then I took him to the train station in Lelles 21.















Generations - 60's 70's and 80's - lelles 21, Dan's hight top late bay and the Syncro,


News this week - other then the big VW diesel scam (plenty of funny jokes going around with that one) me and Lelle got the syncro stuck in the mud! and we had a lot of fun trying to get free.
getting slapped in the face by mud from the front wheels spinning while looking out!

Steve and Lelle getting muddy

It wouldn't have been a problem with some good mud/snow tires fitted - coming soon



I have 3 weekends until the Autumn school break - during that time I plan to move the samba, syncro, tools and lelles buses into a warm, I repeat  WARM! garage in Enköping! At last after 11 years I will experience what its like to beaver away in a warm garage right through the long dark, cold Swedish winter.

The jobs im looking at this weekend is to fix the exhaust blow on the syncro and fit new rocker cover gaskets - I ordered gaskets form the local mekonomen.

Then on to the samba - plenty of Jobs to do, but at the moment its all about getting the jobs completed that will allow me to get the bus off the tip girl and back on its wheels - so the bus can be trailored to the new garage.

These jobs are:

1. Steering arm - check bushes for play then most probably order new bushes, install and re ream. then fit steering pin etc.
2. Gear shift rod - check I have all the parts needed to reassemble, check the length - do I need to order a new front section?  look at how the bushes work and order relative parts.
3. Fitting of 1 drive shaft boots - remove the drums, break down the hubs etc and install the 1 pice rubber boots. Make new side plate gaskets, seal and bolt everything back.
4. Route in the main part of wiring loom and fasten.
5. Continue spraying cavity "waxoil" into any place that can take it.
6.Weld new accelerator brackets.
7. Install the steering box into the bus, make shims and gaskets to lower if needed,  apply gasket sealant and tighten up and check play - fill with lube later???
8. Grind a little material away form flipped spindle so the disk clears - re fit hub to spindle.
9. Install front beam
10. Install gearbox
11. Fit wheels (where are the ones ordered last December?  10 months waiting ??)
12. Check the offset etc of new wheels.






 FOR REFERENCE - HOW TO!
steering arm - bushes etc








New garage space for this winter - should be able to have space for 4 buses + space for working and benches ; )




wheels !!!!!

 Checking the wheel clearance to the spring plate - my original vw steel wheels touch the spring plate adjuster, I fitted a big wheel spacer just to get it to turn - but this was a temp solution to move the bus about - JONNY from Finland has banded steel wheels on the rear of his 56 samba, no problems with offset there.

Moon eyes Japan 
 have 2 types of offset available in the speed master series of wheels.


Speed Master Wheel 15X5 5H205 +13 for Early VW
2 type of offset, +13mm & +21mm is available.
I ordered The JBW From MWS through Cool Air in the UK - INFO SAYS :
                                       
NCA 5x205 JBW 15x5.5inch SMA Wheel Et14
Traditional Retro Design, Superior Craftsmanship. This Traditional Alloy Wheel comes painted In Sand Brushed Silver with High-lighted Rim & Bolt on Centre Cap. Type: SMA Colour: SAND BRUSHED SILVER HI-LITE Size: 5.5 x 15 PCD: 5-205 Offset: ET14 
 Fitment: VW BEETLE -Up to 68, VW SPLIT- Up to 68,VW BAY- Up to 70. 
 Not currently available as of 07.09.15

Also I missed out on this nice middle seat advertised on blocket
I called 10 mins too late - damit !
I hope it went to someone who needed it!






 

söndag 20 september 2015

Syncro joins the rides and rivnuting

Spent a few hours this weekend drilling and fixing rivnuts to the side belly pans

onsdag 5 augusti 2015

Summer time, Bussfest 2015 and Garage time.

Schools out for summer !

 we kicked summer of with trips to the local beach in Enköping, relaxing into the summer vibes.



Then a little excursion down south, fixing a deal on a BSA Spitfire for my dad and visiting Roland and his new house in the same weekend

 


 Back in the garage the boys find Barry´s gag bike



   







 
and I get cracking on the bus again, moving from corner to corner, looking at the brake servo and copper hard line installation as well as the fitting of glass in to pop outs and safaris, also looking at the door locks.

 Then we had a trip home to Cambridge, UK

STREET ART IN CAMBRIDGE

Buskers in Cambridge

Trish my sister

Enjoy the river Cam by Punt

Dads new fabricated seat for his guzzi cali




Back in Sweden and a nice time with Esty and the Chileans at Gröna lund watching Robert Plant
Then it was time for this years bussfest - Båstad, I had planned to take lelles samba along, loaded up with stuff for bussfest, but a few miles out of town and I had a breakdown, turned out to be that there was no fuel filter fitted ! DOH! so loads of crap from the tank had been finding its nerry way to the carb, no good and had to abandon and take the golf instead.



 Finally at bussfest and straight down to buisness, here we all are fixing the goodie bags for bussfest


















 I will write up a full post about this years bussfest in the near future, but what I can say now is that it was as usual a great meeting, not to be missed!


Back in the garage and things are progressing, fired up afetre bussfest and on a mission to have it driving for the next one ???

nice job installing the hard lines from mc to servo, this bus is gonna stop well!


vac hose getting routed in
 Then I started on the belly pans, going for the removable idea, so I got tooled up with a rivnut set and got busy making the pans fit, getting there with the sides but the center section is going to need a little more fabrication to get it to be removable.

bus over on its side

getting organized with new shelves for the garage

Happy with the belly pan fitment

Next up is to continue drilling and rivnut-ing, finishing the brake lines, order and recive more parts and everything that is required on getting the bus back to a place where the under side jobs are done and the bus can meet its wheels once again, some of the jobs I have to do are fitting the 1 piece axle gators to the drive shaft tubes, installing the steering box and aligning the shaft, welding new brackets for the accelerator linkage and making sure the gear shift, brake pedal and clucth pedals all fit and do like they should, also will be routing the wiring loom in too, belly pans will head for paint as soon as they are fabricated -

also just had a great find, got a 6 v wiper motor and missing mounting plate for 300 kr at bug run classic, after about 30 mins I had them all cleaned up and straightened, looking forward to getting the 12 v armature and installing that little lot under the dash.