onsdag 5 augusti 2015

Summer time, Bussfest 2015 and Garage time.

Schools out for summer !

 we kicked summer of with trips to the local beach in Enköping, relaxing into the summer vibes.



Then a little excursion down south, fixing a deal on a BSA Spitfire for my dad and visiting Roland and his new house in the same weekend

 


 Back in the garage the boys find Barry´s gag bike



   







 
and I get cracking on the bus again, moving from corner to corner, looking at the brake servo and copper hard line installation as well as the fitting of glass in to pop outs and safaris, also looking at the door locks.

 Then we had a trip home to Cambridge, UK

STREET ART IN CAMBRIDGE

Buskers in Cambridge

Trish my sister

Enjoy the river Cam by Punt

Dads new fabricated seat for his guzzi cali




Back in Sweden and a nice time with Esty and the Chileans at Gröna lund watching Robert Plant
Then it was time for this years bussfest - Båstad, I had planned to take lelles samba along, loaded up with stuff for bussfest, but a few miles out of town and I had a breakdown, turned out to be that there was no fuel filter fitted ! DOH! so loads of crap from the tank had been finding its nerry way to the carb, no good and had to abandon and take the golf instead.



 Finally at bussfest and straight down to buisness, here we all are fixing the goodie bags for bussfest


















 I will write up a full post about this years bussfest in the near future, but what I can say now is that it was as usual a great meeting, not to be missed!


Back in the garage and things are progressing, fired up afetre bussfest and on a mission to have it driving for the next one ???

nice job installing the hard lines from mc to servo, this bus is gonna stop well!


vac hose getting routed in
 Then I started on the belly pans, going for the removable idea, so I got tooled up with a rivnut set and got busy making the pans fit, getting there with the sides but the center section is going to need a little more fabrication to get it to be removable.

bus over on its side

getting organized with new shelves for the garage

Happy with the belly pan fitment

Next up is to continue drilling and rivnut-ing, finishing the brake lines, order and recive more parts and everything that is required on getting the bus back to a place where the under side jobs are done and the bus can meet its wheels once again, some of the jobs I have to do are fitting the 1 piece axle gators to the drive shaft tubes, installing the steering box and aligning the shaft, welding new brackets for the accelerator linkage and making sure the gear shift, brake pedal and clucth pedals all fit and do like they should, also will be routing the wiring loom in too, belly pans will head for paint as soon as they are fabricated -

also just had a great find, got a 6 v wiper motor and missing mounting plate for 300 kr at bug run classic, after about 30 mins I had them all cleaned up and straightened, looking forward to getting the 12 v armature and installing that little lot under the dash.

måndag 29 juni 2015

Brakes, steering boxes, books, food trucks and finding more sponsors for Bussfest!

Brakes!

So I began looking how to go about the installation of the dual circuit brake servo -
I got mine from the talented and very helpful VW Jim - UK along with a bunch of fitting parts who I can totally recommend.  here is a link to Jims very handy site and his own "how too"  VW JIM

Once fitted and set up this vacuum assisted servo should provide much more power assistance to the brakes.

First I need to find a place to fit the servo, I was thinking about how the hoses and hard brake lines connect, I found the area suggested in Jims how to to be perfect, just behind the beam on the passenger side - I test fitted as I was a little worried that the drill holes would end up in some awkward place in the locker area under the seat, but I was lucky and everything looked ok.

Finding a suitable place and then marking the positioning.
 


 Then removed the mounting bracket and marked where the bolts will go through the floor.

 Then dot punched                                                    and drilled.



 After drilling out to the size, I painted the bare metal with some black paint.
 All thats needed now is an extra pair of hands to tighten the nuts, bolts and washers.

I then moved on to looking at the steering box, to do this I needed to fit the parcel tray which goes under the dash, the old self tapped welded nuts were missing so I have used some nylock nuts and washers on the back side, after a bit of fiddling I had the shelf in place.

 Then I tipped the bus on its side and slid in the steering box, loosely fitted in place to see how it lines up, it was a little over to the left of the dash pod, but I think I can adjust this and center it by sliding the steering box in the bracket on the under side.
 Looked good, so then I removed the box again and dismantled it, cleaned out the dirt and sand which had accumulated using petrol, made up a shaft with a piece of sponge to clean the inside of the shaft.
 checked the inner shaft, bearings and cup are all new.
 clean inside, then greased it a little using the same make shift cleaning rod.
 Then I took apart the box, cleaned everything in petrol and slightly sanded the mating surfaces, after this I re-greased the bearings and re installed the lot.
 cleaned up the worm gear
 All good, new bushes and seal
 Looked on the net about whats best to pack the box with, going to go with gerbox 90 grade oil once I have the new gaskets.
 Here you can see the metal shims, I have 4 but 3 are broken, looking for new ones at the moment.
I also digged into the wiring loom box and found the horn wire and installed this too, ready - the loom guy had made things nice and easy by carefully and thoughtfully labeling all the wires ; )



This week me and the boys went into town to grab a bite to eat at lunch, we headed straight for the food truck that was parked in the town square and what would you know! our book was there on display


 

 Also this week its been full force getting the last parts to the sponsoring of this year bussfest  in Båstad, Ive been busy ringing around and sending out emails trying to get some more sponsors for this years VW bus meet.

So far this year we have sponsors form VW Sweden, custom and speed parts-Sweden, The local VW dealer - michelsensbil.se, long time sponsor of tires - gusonibromma.se, and of course us -vwcampercookbook










söndag 21 juni 2015

Midsummer part 3

Summer time = Garage time

Despite the rain holding out today,  we didn't make it to the Sunday mini moto practice to ride as we still need to fix some of the issues from last weeks crash, Travis needs a new visor to his helmet and a kill switch for the bike.

Me and Lewis took a trip anyway with out the bikes to the track in Västerås to check out a bigger set of leathers fro him, which worked out great, now he will be able to move a little easier then in the old tight set he has been riding in.



In the afternoon i got working a little more on the front fairing, sanding it down and finding out where it needs to be patched with fiberglass.


After rubbing that down for a while I switched my attention to the bus, I am working on the underside at the moment, all areas.


started seeing how the belly pans offered up, then began making them fit better.



 Also began seeing where I will fit the brake servo, vacuum pipe, brake pipes etc etc
needed to grind down the servo so the new bracket could fit nice.





 Great to be able to spin the bus over and work easily on the under side